# Bond Pro with SOMFY Movelite 35 wireless **URL:** \ **Category:** Welcome & Introduction\ **Created:** [February 6, 2026, 3:08pm UTC](https://forum.bondhome.io/t/bond-pro-with-somfy-movelite-35-wireless/5834 "2026-02-06T15:08:17Z")\ **Posts on this page:** 4\ **Page:** 1
**Author:** ![Rudolf](https://avatars.discourse-cdn.com/v4/letter/r/5daacb/32.png) [@Rudolf](https://forum.bondhome.io/u/Rudolf)\ **Post date:** [February 6, 2026, 3:08pm UTC](https://forum.bondhome.io/t/bond-pro-with-somfy-movelite-35-wireless/5834/1 "2026-02-06T15:08:18Z")
I installed 4 Somfy Movelite and a Bond pro. The commands only get to the motors from time to time. Sometimes it works. sometime not, sometimes after 4 commands sent. It’s very annoying to program a schedule which then is not working. The bond pro is visible from the motors ± 3 to 5 meters. The somfy remote is working. Anyone has this problem too and a solution ? Thanks for your support Rudolf ---
**Author:** ![Joachim47](https://avatars.discourse-cdn.com/v4/letter/j/c4cdca/32.png) [@Joachim47](https://forum.bondhome.io/u/Joachim47)\ **Post date:** [February 7, 2026, 3:00pm UTC](https://forum.bondhome.io/t/bond-pro-with-somfy-movelite-35-wireless/5834/2 "2026-02-07T15:00:55Z")
Hi Rudolf, welcome to the forum! In order to understand your situation better, please give us some details about the failure situation: 1. all 4 motors operate on their own Somfy remote? 1. operating 1 motor at a time with Bond, does it shows the same iffy work-notwork behavior? 2. are you grouping motors via remote or Bond? ---
**Author:** ![Rudolf](https://avatars.discourse-cdn.com/v4/letter/r/5daacb/32.png) [@Rudolf](https://forum.bondhome.io/u/Rudolf)\ **Post date:** [February 9, 2026, 9:39am UTC](https://forum.bondhome.io/t/bond-pro-with-somfy-movelite-35-wireless/5834/3 "2026-02-09T09:39:08Z")
Good morning Joachim Thanks for your feedback. The installation is as follows: 2 Movelite WireFree 35 RTS with a somfy Situo 5 RTS Pure II on channel 1 and 2. There is a grouping on the situo for all curtains. This is working fine. 1 Bond pro, connected to the 2 Movelite WireFree 35 RTS. I don’t use grouping. The test now: close not working, open not working (it’s open), 2 more times, then closing is working, the manual commands in the Bond App are now working. I set the schedule, bond pro is flickering, no reaction of the motor! It’s absolutely unpredictable… I have also a standard Bond with somfy blinds, this is working better, only the distance is not good, that’s why I bought the pro for the newly installed curtains. Thanks for your help ---
**Author:** ![Joachim47](https://avatars.discourse-cdn.com/v4/letter/j/c4cdca/32.png) [@Joachim47](https://forum.bondhome.io/u/Joachim47)\ **Post date:** [February 9, 2026, 1:58pm UTC](https://forum.bondhome.io/t/bond-pro-with-somfy-movelite-35-wireless/5834/4 "2026-02-09T13:58:36Z")
Good morning Rudolf! It seems, you have signal quality problems. Let me explain my experience with operating 5 Somfy outside shades on the periphery of my 1 story 2900sqf home with a Bond in the center which requires the signal to passing at least 2 walls with cabinets. 1. All shades are individually connected to the Bond as shade(1,2,3,4,5) and are proven to work each individually on a Bond command. This proved that the learning process of each has been successful. 1. Then I created 2 groups on the multichannel remote, named shade13 and shade45 which represent the actual use conditions of simultanious open/close operation due to east/south orientation. 2. Then learning Bond these new quasi shades. 3. With that the operation is working flawlessly on Bond and Alexa with Bond skill. This procedure accomplishes 2 things: a} actually true simultaneous operation (no popcorn behavior) b) minimal signal interference (avoiding multiple signals from Bond to trigger each shade individually)